Tube FZH or Röhre FZH ID, IC – Integrated Circuit, SPECIAL TUBEBASE in general and Universal shown. Radio tubes are valves. Part Number: FZHA Function: DIP 16P Maker: Siemens AG Pinouts: FZHA datasheet. Description: Datasheet PDF Download. FZH Datasheet, FZH PDF, FZH Data sheet, FZH manual, FZH pdf, FZH, datenblatt, Electronics FZH, alldatasheet, free, datasheet.

Author: Nigis Gogor
Country: Sierra Leone
Language: English (Spanish)
Genre: Automotive
Published (Last): 2 November 2016
Pages: 457
PDF File Size: 2.86 Mb
ePub File Size: 9.2 Mb
ISBN: 684-3-87151-958-5
Downloads: 66988
Price: Free* [*Free Regsitration Required]
Uploader: Gagul

【FZH106A】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

No external components for frequency compensation are required. Figure 4 shows an extension of the circuit to 24 diodes with 2 UAA TDA contains a controlled RF pre and intermediate stage, a multi- plicative datwsheet mixer with separate oscillator, controlled IF amplifier, full-wave de- modulator, active low pass, as well as an amplifier to directly feed a field-strength indicator instrument.

Each stage can be selected with very low current. Suitable voltage dividers allowany possible adaptation, as e. It may be used, for example, in video distribution networks.

FZH , Tube FZH; Röhre FZH ID, IC – Integrated

As can be seen, the temperature drift is inferior. An internal ring counter allows con- tinued switching from channel to channel. Ring scales are obtained by a circular ar- rangement of the diodes. By selecting a memory, the respective operational amplifier is connected to the operating re- sistance.

Full text of “Siemens Analog Integrated Circuits Data Book “

Applications of this kind can be used fzh1111 level sensors, VU-meters, tachometers, radio scales etc. Each integrated circuit vzh111 4 channel memories. Switching through of the tuning voltage The switching through of the tuning voltage was subject to particular care during develop- ment. The AF outputs are referred to ground and stabilized against hum of the supply voltage. P and N types are able to control the PIN diode attenuators common today without additional transistors.

  000-610 DB2 10.1 FUNDAMENTALS PDF

Current limit transistor datashret be used for shutdown if current limiting is not required. Package 5 H 8 DIN and similar cases with 8, 10 and 12 pins The position of the case is arbitrary. Thus, cross-talking can be improved. The RS flipflop is set by T 6. The threshold is fixed with a voltage proportional to the supply voltage.

Datasheet archive on 9-9-2013

The leads are connected to the printed circuit by iron soldering or spot welding. D10 D11 D12 4 Ring scales are obtained by a circular arrangement of the diodes. A decrease of 30 dB requires a resistor between pin 5 and ground with a resistance value depending on the group number as shown below.

Applications of this kind can be used for level sensors, VU-meters, tachometers, field strength indicators etc. Republic Tihama Tractors 8- Engineering Co. Iron or dip soldering may be applied. The symmetric composition of the circuit allows a high stability against oscillating and, at the same time, an AGC range of more than dB. It includes a pre-emphasis to balance the de-emphasis at the AF-output. The push-pull mixer is operating multiplicatavely. In addition, these circuits contain a voltage stabili- zation and are especially well suited for an application in proximity switches, light beam- and other contactless switching applications.

Input voltages beyond the selected display range cannot be determined. Two outputs are available for each stage: Between pins 10 and 14 ground and between pins 12 and 14, a resistance of at least Q may be connected to increase the currents and therefore the conversion transconductance.

The first two letters identify the family. S is particu- larly suited for sets where a low current consumption is of importance, or where major supply voltage fluctuations occur. Without phototransistor suffices a fixed resistance which must have approx.

Bending of the leads When bending, the leads must not be stressed between leads and case.


The actual value can only be measured during the passage from D1 to D2. There- fore, it is possible to provide the first and third quartet lighting red and the second quartet green in order to mark a working range.

The IC’s can be lined up in any number. Plastic plug-in package Plastic packages are soldered on the side of the printed circuit board opposite to the case, the pins are vertically bent and fit into holes at an equal distance of 7.

Receiving quality The figures shown in the table are warranty-figures. The input volt- ages at pins 11, 12 and 13 are freely selectable in the range between and 6 V. With adequate external circuitry several IC’s can be connected in series.

Voltage at datasueet 14 without colour sync signal with colour sync signal peak-to-peak value of 0. AQL, critical electrical defects: Additional terminals are provided for triggering or resetting if desired.

After dwtasheet the case into the printed circuit board two or more leads should be bent at an angle of app. The TDA offers provisions for the feeding of an amplitude indicator, either positive or negative going mono-stereo voltage, AFT output push-pull-current output with automatic switch-off, squelch adjustable for more than 40 dB range of input signal and depending on detuning. SAS S only: By the AGC of prestage an ex- cellent large signal handling is obtained.

The distance daasheet the package and the printed circuit board is determined by shoulders see picture. The new ICs offer with even less external circuitry higher operating comfort: