ASTM A666-10 PDF

ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.

Author: Megor Zugrel
Country: Vietnam
Language: English (Spanish)
Genre: Environment
Published (Last): 17 March 2006
Pages: 357
PDF File Size: 15.90 Mb
ePub File Size: 20.64 Mb
ISBN: 594-2-50249-296-8
Downloads: 89487
Price: Free* [*Free Regsitration Required]
Uploader: Goran

Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres. Originally approved in Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to aastm atmospheres Chemical Composition: Types and L cannot be hardened by thermal treatment.

  INTERMATIC DT500CH PDF

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. Individual reprints single or multiple a6666-10 of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

HardC Elongation in 2 in. Hard Elongation in 2 in. Last previous edition approved in as A — A number in parentheses indicates the year of last reapproval.

A — 10 Standard Speci? Only annealed conditions of grades speci?

Number of Tests 8. This standard has been approved for use by agencies of the Department of Defense. Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part.

However, in the case of dispute, tests shall be made by pressure. In case of dispute, the offset method of determining yield strength shall be used. Material Test Report and Certi? The choice of test method for materials in conditions other than annealed shall be at the option of the seller.

HRC typical L Ann 25 min. Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. These alloys represent an excellent combination of corrosion resistance and fabricability.

  EHEIM 2026 PDF

If filler metal is a666-0, Type is normally used. The values obtained in this manner should not, however, be taken as the actual yield strength for 0. C Annealed material that naturally meets mechanical properties may be applied.

Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Find out what NKS can do for you.

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

This revision of Speci? Maximum unless otherwise indicated. One bend test shall be made from one end of each coil. The values given in parentheses are for information only. Rockwell B 95 95 B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?

Current edition approved Sept.