ASTM B265 PDF

ASTM Gradel, JIS Grade, TIA, RMI 25, TIMETAL 35A, ST Sheet and plate. ASTM B Gr1, Mil-T CP Bars and billets. ASTM B Gr1. Tube. ASTM B Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality Titanium Plates, Sheets & Coils, Titanium sheets & plates.

Author: Sagami Tygot
Country: Tanzania
Language: English (Spanish)
Genre: Automotive
Published (Last): 25 February 2014
Pages: 82
PDF File Size: 18.14 Mb
ePub File Size: 20.16 Mb
ISBN: 193-7-45906-874-2
Downloads: 92546
Price: Free* [*Free Regsitration Required]
Uploader: Misida

Aluminum Vanadium Palladium Ruthenium 0. The markings shall have no deleterious effect on the material or its performance. The characters shall be sufficiently stable to withstand ordinary handling. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

This specification covers annealed titanium and titanium alloy strip, sheet, and plate.

TITANIUM ALLOYS TECHNICAL DATA

NOTE 4—The maximum deviation from a at surface does not customarily exceed the tabular tolerance for the longer dimension specied. Each pair of these v265 will place opposite surfaces of the sheet or plate material in tension. Unalloyed titanium plus 0. Grades 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use.

The surface of the specimen must include the original material surface with no material removal or surface conditioning, except corners may be rounded to a maximum radius of 0. Grade 2H, 7H, 16H, and 26H are intended primarily for pressure vessel use. Approved April 15, Silicon each total 0. Bend tests are not applicable to material over 0. This standard has been approved for use by agencies of the Department of Defense.

  EK GADHE KI SARGUZASHT PDF

ASTM B – 15 Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate

The chemical analysis shall be conducted by the standard techniques normally utilized by the manufacturer and purchaser.

There is no under tolerance in weight for titanium sheets, under tolerance being restricted by the permissible thickness variations. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. asmt

Asm is in accordance with the round-off method of Practice E For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown. Last previous edition approved in as B — 09a1. The v265 of titanium and titanium alloy metal covered by this specification shall have the chemical composition requirements of: The report shall include results of all chemical analysis, tensile tests, and all other tests required by the specication.

Committee B10 has identied the location of selected changes to this b2665 since the last issue B – 08b that may impact the use of this standard. For plates of irregular shape, the over thickness tolerances apply to the greatest width corresponding to the width ranges shown.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Alternate techniques are discussed in Guide E Final product hydrogen shall be reported.

D Other elements need not be reported unless the concentration level is greater than 0. If shipped as descaled, sandblasted, or ground, the manufacturer shall be permitted to remove minor surface imperfections by spot grinding if such grinding does not reduce the thickness of the material below the minimum permitted by the tolerance for the thickness ordered.

  DONDE VAN A MORIR LOS ELEFANTES JOSE DONOSO PDF

Titanium Plates, Sheets & Coils

The width of the bend test specimen shall be at least 5 times the thickness. A superscript epsilon indicates an editorial change since the last revision or reapproval. Other elements may be present in titanium or titanium alloys in small quantities and are inherent to the manufacturing process.

The values given in parentheses are mathematical conversions to SI units that are adtm for information only and are not considered standard.

Surface Requirement Bend Tests S1. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

NOTE 2—If the longer dimension is under 36 in. Referee Test and Analysis Samples shall be taken from the ingot or the extremes of the product to be analyzed. Samples for analysis should be stored in suitable containers. Special Flatness Requirements S3. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.