EN 60268-7 PDF

Find the most up-to-date version of CEI EN at Engineering IEC Sound System Equipment – Part 7: Headphones and Earphones is an international standard intended to characterize the. IEC SOUND SYSTEM EQUIPMENT –- PART 7: HEADPHONES AND EARPHONES.

Author: Kale Gardakree
Country: Haiti
Language: English (Spanish)
Genre: Health and Food
Published (Last): 27 January 2008
Pages: 417
PDF File Size: 3.46 Mb
ePub File Size: 1.48 Mb
ISBN: 989-9-64042-326-2
Downloads: 32821
Price: Free* [*Free Regsitration Required]
Uploader: Kagul

Search all products by. Now, let us look at the differences. The sequence first plays a stepped sine through both channels of the DUT and captures the sound radiation from the DUT using 2 reference mics. Software Requirements SoundCheck It then calculates the voltage required to produce 1 mW into the rated impedance. Free to use BIM project management tool provides step-by-step help to define, manage and validate responsibility for information development and delivery at each stage of the asset life cycle in level 2 BIM projects.

Document Status Indicators The Green document status indicator indicates that the document is: Worldwide Standards We can source any standard from anywhere in the world.

Want access to British Standards? Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual.

Registration required The content you have requested is available only to registered visitors. Sound System Equipment — Part 7: Please complete the short form 60268- all fields are required. Whereas loudspeakers are tested in open air, a headphone or earphone must be presented with an acoustic load that simulates the human ear.

The standard itself is a lengthy document, 9 Sections and 3 Annexes covering 46 printed pages. Calibrate the microphones per the instructions in the SoundCheck manual. A series of post processing steps calculates the attenuation curves, their average values and shows them on the final display. Headphones and earphones Status: Figure 1a and b: The primary difference in the test set up between a loudspeaker and a headphone measurement is in the way in which the transducer interacts with the microphone.


Find Similar Items This product falls into the following categories. Marking, Microphones, Audio systems, Ratings, Designations, Instructions for use, Headphones, Classification systems, Frequency response, Earphones, Audio equipment, Voltage measurement, Impedance measurement, Testing conditions, Preamplifiers, Comparative tests, Acoustic measurement, Electrical wave measurement, Electrical properties and phenomena, Acoustic testing.

In order to add these Signal Paths to your System Calibration or relink to existing Signal Paths, you should open each of the sequences individually and, if prompted, add or relink Paths to your System Calibration. A statistics step calculates the mean of the 3 unoccluded measurements. Setup System, Hardware and Calibration Before attempting to run any of the eh, read the following setup instructions. The spectra are then power summed to derive a single SPL value and the Hz fundamentals are post processed to derive their SPL values.

Test Setup for measuring headphone voltage sensitivity. Noise speakers are set up adjacent to the HATS left and right ears. It is recommended that the sequences be run directly from the IEC folder. Headphones and 60268- incorporating corrigendum November Comparison between an ideal loudspeaker free-field measurement and the same measurement in the ear of a head-torso simulation device.

The data from each loop iteration is displayed as it is acquired. If more than 4 60268- channels are available, all input signal paths may be assigned to separate hardware channels. The sequence prompts the operator to enter the rated voltage and rated impedance of the DUT.

Click to learn more. The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: In Part 2 we address the specific needs of special cases of headphones such as Bluetooth and USB headphone testing, noise-cancelling headphones, and Max SPL measurements to prevent hearing loss.


The user is first prompted to enter the rated voltage.

Supersedes BS EN In this article, Steve Temme discusses the issues that are common to testing all types of headphones. Five separate sequences are provided, each designed to measure specific characteristics.

Sound system equipment – Part 7: Headphones and earphones

Headphone Voltage Sensitivity Final 602687. This sequence uses a pink noise stimulus to characterize the passive, active and total attenuation of noise cancelling headphones. As more and more loudspeaker engineers find themselves employed in the fast-growing headphone market, it is important that the unique challenges of testing headphone packages are fully understood. Please download Chrome or Firefox or view our browser tips. The content you have requested is available only to registered visitors.

Once calibrated, position the microphones enn.

The Red document status indicator indicates that the document is an old version The document has likely been withdrawn by the publisher, also the meta data presented here may be 602668-7 of date as it is no longer being maintained by the editorial teams at NBS.

The basic measurements made on headphones are very similar to those made on loudspeakers.

IEC Headphone Test Sequences – Listen, Inc.

SoundCheck screen for headphone response measurement. This value is converted to dBV and used to calculate the IM and difference frequency stimulus levels.

If passive, connect to the headphone amp or separate audio power amplifier You are ready to start the sequence. Their 602688-7 work with the manufacturing and service industries, government, businesses and consumers to facilitate the production of British, European and International standards.